BURKS 330CS7M-FE 1.25" Turbine Pump and FE 460V Motor 3 HP 12-GPM Remanufactured

Description

Our Store
Our Feedback
Add Us To Your Favorites
New Arrival
Ending Soon
BURKS
330CS7M-FE Turbine Pump and Franklin Electric Motor 3 HP 12GPM
Features :
Pump Body:Cast Iron Impeller:Bronze Shaft Seal:Buna/N/Carbon/Ceramic/SS Mechanical Seal Port Size: Ports are 1-1/4 Inch NPT Inlet, 1 Inch NPT Outlet Motor / Amp Draw: 3 Horsepower, 3500 RPM RPM, 460 Volts, Three Phase, ODP Open Drip Proof.
Product Specs :
Raceway Sealing grooves, machined into the face of the raceway, match the impeller sealing grooves, minimizing water slippage and increasing delivery efficiencies.
Impeller Annular grooves or sealing rings, machined into the face of the impeller are perfectly matched with corresponding grooves in the raceway and intermesh without metal-to-metal contact to form a labyrinth seal.
Extended LifeLok adjustment allows for extended life, field adjustment, and restoring factor efficiency as hydraulic passage wears.
FACTORY RE-MANUFACTURED - COMES MOUNTED ON BOARD in GENERIC BOX
BURKS 330CS7M-FE 1.25" Turbine Pump and FE 460V Motor 3 HP 12-GPM Remanufactured
Burks # 330CS7M Turbine Pump and Motor 3 HP
The Burks 330CS7M is a Cast Iron Turbine Pump and Motor with a Bronze Impeller, Buna-N/Carbon/Ceramic/SS Mechanical Seal, 1-1/4 Inch NPT Inlet, 1 Inch NPT Outlet Ports, close coupled to a 3 Horsepower, 3500 RPM, 208-230/460 Volts, 3 Phase, ODP Open Drip Proof, 60Hz Motor. This pump has a maximum performance of up to 12 gallons per minute water flow at 350 feet of head (151 PSI). The motor on this pump has open drip proof construction and is rated with jet pump service factors for continuous duty operation at all ratings shown. The three phase motor on this pump requires a magnetic type starter which provides full 3-leg overload protection. This compact turbine pump is designed for pumping clear water and many other nonabrasive, lower viscosity liquids on high pressure, low capacity applications with the greatest possible efficiency. The Bronze impeller with Monel blades is the only moving part and the Bronze raceway with cast-in vortex pockets will not vapor lock. This pump's unique design is engineered for many applications requiring higher pressures and lower capacities impossible for other single stage pumps of a similar size, and the pump's compact space-saving size without a coupling eliminates misalignment problems. The operating temperature limits of this pump depend on the seal elastomer and the following temperature limit applies for Buna-N Seals : 225 degrees F (107 degrees C). The pump shaft seal is a mechanical seal with ceramic seat and carbon seal face for maximum durability, and long trouble-free service. While this pump can be run dry for short periods of time, a lack of liquid will damage the Mechanical seal. The wetted material in contact with the liquid are Cast Iron, Bronze, 303 Stainless Steel, and Buna-N. The dimensions of this pump are 21 inches long, 9 inches high, and 6-1/2 inches wide.
WEIGHT : This pump and motor unit weighs 72 Lbs.
Applications
Designed for versatile, high performance applications these Burks CS series Turbine Pumps are designed for pumping any clean, noncorrosive, nonabrasive lower viscosity liquid on low flow, highhead applications. They are used is a wide range of industries on applications such as hightemperature water and oil heat transfer applications, Boiler feed and condensate return circulation, Hot and cold water circulation, brine recirculation, hydraulic oil circulation. They can be used in many metering applications such as additive metering and hot water spray, or in pressure maintenance applications such as being used as jockey pumps, or for pressure boosting. These are just a few of the most common applications. The durable materials of construction, long service life, and low maintenance design make the Burks Turbine Pump an excellent choice for numerous clean water applications. These pumps are designed for low maintenance and long service life. To operate the pump raceway conducts fluid into the impeller and then provides a channel for the liquid to move as it is propelled and energized by the impeller. The Burks Regenerative Turbine Pump is unique in design and is engineered for high pressure, low flow applications. An integral part of their unique design is the LifeLok feature that provides a way to externally adjust the clearance between the impeller and raceway. Burks is the only regenerative turbine pump that has this feature. This adjustment is used for precise setting of pump performance during production testing. LifeLok makes the Burks Turbine Pump field adjustable. Because of the lowflow, high head characteristics of the regenerative turbine, the pump pressure may be adjusted when necessary to match critical system requirements without appreciably changing the flow rate. LifeLok also allows pump performance to be restored to like new after years of service, greatly extending pump life. There is an adjusting screw that is located in the shaft extension end of the motor on CloseCoupled Pumps. A positive preload spring pressure is applied to the pump shaft bearing and, in turn, is transmitted to the adjusting screw. This controlled pressure eliminates bearing end play and provides a means for external adjustment of the clearance between the impeller and raceway. Burks Turbine Pumps are of the positive displacement type. When the pump is operating, liquid will be delivered to the discharge side of the pump. If the discharge line is blocked or closed, pressure will build up until the motor stalls, a pump part breaks or the piping bursts. To prevent the possibility of equipment damage or personal injury, a pressure relieving device of adequate size must be incorporated in the discharge side of the system. NOTE A strainer, approximately 20 mesh, should be installed on the suction side of the pump to prevent chips, scale or hard foreign particles from entering the pump and damaging the raceway and impeller.___   ______________________  ___
MD Industrial Salvage often purchases entire inventories of high end Industrial, Electrical, Automation, Manufacturing, and PLC processing parts and supplies from businesses in transition. These could be factories, machine shops, distributors or stores that are moving, updating or closing. Although the businesses may no longer have any use for the items we purchase, they are sitting in the maintenance department or store room awaiting use. For the most part these inventories are generally new, and in the original package. Occasionally items we purchase are used, and placed on the parts shelf as backups, and will be listed as used on our listing. Some of the original packaging may have writing, shelf wear, tears or stains, but the product inside is in new condition, unless listed as used. We offer these items at a greatly reduced price off of wholesale and retail. We guarantee these parts and supplies to be new, unless noted, and in working condition. If it is used, it was placed in the parts area as a working spare and is ready, We offer a 100% return and refund policy, no questions asked, so bid with confidence!
To see our other electrical, industrial parts and supplies
CLICK HERE
to check out our store!
And don't forget to add us to you favorites if you are on the watch for parts and tooling. Our inventory is ever changing and we honestly
NEVER
know what we have coming around the corner.
General Shipping Rules
Shipping is provided by USPS First Class and Priority for smaller items under 16oz.,
you may choose
at check out.
Shipping is provided by USPS Parcel Select , Priority, and FedEx for larger items up to 150lbs.,
you may choose
at check out.
Shipping is provided by Freight Carrier on much larger and heavier items over 150lbs.
For a quote please provide us your
zip code
,
whether it's a business or residence
and,
if a business does it have a fork lift or dock
.
Local pick up is available on most items by scheduling a pickup time
, we are located in
South Baltimore
off
Russell St.
(295) near the Casino and Stadiums. Ebay restricts sharing our address prior to the sale. Once the sale is complete we will certainly give you our exact address for local pick-up purposes. Shipping fees will be waived or refunded.
International Shipping
We gladly ship international, and is available on all our products. Our products should have an international shipping cost to your location and address that you have registered with eBay as your ship to address. If you do not see a shipping cost,
please request a quote
.
General shipping rules apply, unless listed or noted otherwise
.
Return/Refund & Feed Back Policy
We absolutely want you to be 100% satisfied with your purchase. If for any reason you are unhappy with your
purchase once it arrives
,
we ask that you please email us
, call us with the number provided with your item on the packing slip/invoice, or if you've misplaced it, you can request our contact information, including number, through the advance search at the top of the page
. Our hours of operation for phone contact are Mon-Fri 9am-3pm Eastern Standard Time. Please, before getting upset or leaving negative feedback, call or email us and give us the opportunity to make things right and or issue you a full refund.
Contact
While we love to hear from our customers, eBay policy strictly prohibits sharing contact information prior to the sale. If you have any questions prior to the sale, w
e ask that you please email us through eBay.
Once the sale is complete you can request our contact information, including number, through email or the advance search at the top of the page. If for any reason you are unhappy after your purchase, or after speaking with us, we can easily cancel your sale and refund 100% of your purchase and shipping.
We
are available by email and phone Mon-Fri 9am-3pm EST.
About Us
Md Industrial Salvage is a different type of recycling company. We have operated in
Baltimore
and surrounding areas since 1996. After starting out rescuing fireplace mantles and cast iron door locks from construction dumpsters, we have opened our eyes to may types of waste that are often over looked and fall through the cracks. Our focus is, and always will be vintage items of the highest quality. But with our eyes now open we put a lot of effort in bringing you high end industrial and electrical parts as well. All our items are salvaged and are for the most part American Made. One week we could be in an old School or Brewery, the next week a Factory, and the following week and Shipyard or Power plant, you just never know. Also, one day we may be removing Vintage lighting, the next day Signs and Vintage blueprints and the following day cleaning out a machine shop or high end parts room. We literally have NO idea what we have coming around corner, so make sure you add us to your favorites and check back often.
Also, check out sister sites,
mdarchitecturalrescue
. If your looking for things of a more a collectible nature visit the store by
CLICKING HERE!
Also check out
balmerglass
if you're looking for some unique or interesting glass items. You can visit the store by
CLICKING HERE!
To see additional eBay items I have listed in my
mdindustrialsalvage
store
CLICK HERE!